892471/836796/833900 ONE (1) NEW OEM LARGE WHEEL CYLINDER WITH 13/16" BORE AND METRIC MOUNTING HOLES CUSHMAN PART M10-1.0 THREADS FOR BRAKE LINE END TRUCKSTER HAULSTER DAIHATSU 327 OR OTHERS.
ALSO TO REPLACE CUSHMAN PART # 833900 WITH 15/16" BORE THAT IS NO LONGER AVAILABLE.
Here are the measurements:
The whole body length is 2.78" if you compress both boots and measure from the end of one boot to the other end of the other boot.
The threads holes are 1.24" apart if you measure from center of one hole to center of other hole.
The outside width of the body is 1.29".
The threaded bolt holes are for M6-1.0 METRIC. So THE 1.0 is the thread pitch (6mm). You would use bolts 833911 that are listed separately.
The brake line hole is M10-1.0 threads, so 10mm.
Some vehicles require a 834161 brake line adapter-(listed separately in the HYDRAULIC BRAKE SYSTEM section) for this.
PLEASE NOTE: IF A WHEEL CYLINDER IS REPLACED ON EITHER REAR BRAKE ASSEMBLY, BOTH REAR WHEEL CYLINDERS MUST BE IDENTICAL TO ENSURE EQUALIZED BRAKING PRESSURE. UNEQUAL BRAKING PRESSURE COULD CAUSE LOSS OF CONTROL OF THE VEHICLE.
LARGE WHEEL CYLINDER WITH METRIC HOLES-NOT FOR MODELS BEFORE 1989, UNLESS YOU KNOW FOR SURE ABOUT YOUR PART NUMBER.
ALSO TO REPLACE CUSHMAN PART # 833900 WITH 15/16" BORE THAT IS NO LONGER AVAILABLE.
Here are the measurements:
The whole body length is 2.78" if you compress both boots and measure from the end of one boot to the other end of the other boot.
The threads holes are 1.24" apart if you measure from center of one hole to center of other hole.
The outside width of the body is 1.29".
The threaded bolt holes are for M6-1.0 METRIC. So THE 1.0 is the thread pitch (6mm). You would use bolts 833911 that are listed separately.
The brake line hole is M10-1.0 threads, so 10mm.
Some vehicles require a 834161 brake line adapter-(listed separately in the HYDRAULIC BRAKE SYSTEM section) for this.
PLEASE NOTE: IF A WHEEL CYLINDER IS REPLACED ON EITHER REAR BRAKE ASSEMBLY, BOTH REAR WHEEL CYLINDERS MUST BE IDENTICAL TO ENSURE EQUALIZED BRAKING PRESSURE. UNEQUAL BRAKING PRESSURE COULD CAUSE LOSS OF CONTROL OF THE VEHICLE.
LARGE WHEEL CYLINDER WITH METRIC HOLES-NOT FOR MODELS BEFORE 1989, UNLESS YOU KNOW FOR SURE ABOUT YOUR PART NUMBER.
ALSO TO REPLACE CUSHMAN PART # 833900 WITH 15/16" BORE THAT IS NO LONGER AVAILABLE.
Here are the measurements:
The whole body length is 2.78" if you compress both boots and measure from the end of one boot to the other end of the other boot.
The threads holes are 1.24" apart if you measure from center of one hole to center of other hole.
The outside width of the body is 1.29".
The threaded bolt holes are for M6-1.0 METRIC. So THE 1.0 is the thread pitch (6mm). You would use bolts 833911 that are listed separately.
The brake line hole is M10-1.0 threads, so 10mm.
Some vehicles require a 834161 brake line adapter-(listed separately in the HYDRAULIC BRAKE SYSTEM section) for this.
PLEASE NOTE: IF A WHEEL CYLINDER IS REPLACED ON EITHER REAR BRAKE ASSEMBLY, BOTH REAR WHEEL CYLINDERS MUST BE IDENTICAL TO ENSURE EQUALIZED BRAKING PRESSURE. UNEQUAL BRAKING PRESSURE COULD CAUSE LOSS OF CONTROL OF THE VEHICLE.
LARGE WHEEL CYLINDER WITH METRIC HOLES-NOT FOR MODELS BEFORE 1989, UNLESS YOU KNOW FOR SURE ABOUT YOUR PART NUMBER.
CUSHMAN THREE WHEELED (SOME FOUR WHEELED) REAR BRAKE PARTS ARE FOR THE FOLLOWING MODELS:
898438, 898439, 898445, 898449, 898450, 898451, 898452, 898454, 898455, 898456, 898457, 898458, 898459, 898461, 898462C, 898464, 898464A, 898464B, 898465, 898465A, 898465B, 898467, 898467A, 898469B, 898474, 898474A, 898474B, 898474C, 898474D, 898474E, 898475, 898475A, 898484A, 898486, 898487, 898488, 898530, 898531, 898532, 898535, 898536, 898537, 898630, 898630A, 898631, 898632A, 898632B, 898633, 898633A, 898633B, 898634, 898634A, 88634B, 898634C, 898635, 898635A, 898636, AND 898637.
PLEASE DOUBLE CHECK THESE PARTS BEFORE YOU BUY. MODELS VARY FROM 1989 TO 1994 APPROX. YEARS THIS FITS.
