ONE (1) NEW 3/16" MAYHEW ROLL PIN PUNCH TOOL WITH FOUR (4) ROLL PINS 3/16" X 1-1/4" CUSHMAN PART # 306971 INCLUDED.

$19.99
Only 2 left in stock

CONTINUE SHOPPING

  • THESE PUNCHES ARE GOOD BECAUSE THEY HAVE THE LITTLE KNOB ON THE END THAT GOES IN THE END OF THE ROLL PIN SO WHEN YOU ARE POUNDING OUT THE ROLL PIN THE PUNCH STAYS IN PLACE AND DOESN'T SLIDE ALL OVER THE PLACE.

  • Roll pins are usually found in the cushman truckster/haulster VEHICLES. THIS IS FOR THE 9HP, 18HP, AND 22HP OMC AIR COOLED ENGINES.

  • May be found on other engines or have other uses.

  • PROP. 65 WARNING. STEEL HARDWARE MAY HAVE CHEMICALS ON THEM TO PREVENT RUSTING.

Quantity:
Add To Cart

CONTINUE SHOPPING

  • THESE PUNCHES ARE GOOD BECAUSE THEY HAVE THE LITTLE KNOB ON THE END THAT GOES IN THE END OF THE ROLL PIN SO WHEN YOU ARE POUNDING OUT THE ROLL PIN THE PUNCH STAYS IN PLACE AND DOESN'T SLIDE ALL OVER THE PLACE.

  • Roll pins are usually found in the cushman truckster/haulster VEHICLES. THIS IS FOR THE 9HP, 18HP, AND 22HP OMC AIR COOLED ENGINES.

  • May be found on other engines or have other uses.

  • PROP. 65 WARNING. STEEL HARDWARE MAY HAVE CHEMICALS ON THEM TO PREVENT RUSTING.

CONTINUE SHOPPING

  • THESE PUNCHES ARE GOOD BECAUSE THEY HAVE THE LITTLE KNOB ON THE END THAT GOES IN THE END OF THE ROLL PIN SO WHEN YOU ARE POUNDING OUT THE ROLL PIN THE PUNCH STAYS IN PLACE AND DOESN'T SLIDE ALL OVER THE PLACE.

  • Roll pins are usually found in the cushman truckster/haulster VEHICLES. THIS IS FOR THE 9HP, 18HP, AND 22HP OMC AIR COOLED ENGINES.

  • May be found on other engines or have other uses.

  • PROP. 65 WARNING. STEEL HARDWARE MAY HAVE CHEMICALS ON THEM TO PREVENT RUSTING.

Here are some of the models this will fit: 880710-880711, 880712, 880714-880720, 880722, 880723, 881007, 881419, 881860, 881862, 881864, 881867 , 898400-898418, 898434-898437, 898440-898444, 898450, 898451, 898452, 898454-898459, 898461, 898500-898502, 898504, 898506, 898507, 898516 , 898530, 898531, 898532, 898535, 898540-898542, 898544, AND MORE. Items are NEW. MODELS ARE LISTED FOR REFERENCE ONLY, YOU ARE RESPONSIBLE TO MAKE SURE THIS IS THE RIGHT PART FOR YOUR VEHICLE BEFORE YOU BUY. THERE ARE MORE MODELS THAT THIS COULD FIT.

812906/882343 ONE (1) NEW OMC 6.5" (6-1/2") OD CLUTCH DISC TO REPLACE CUSHMAN PART. 10 SPLINE. 7/8" HUB TRUCKSTER HAULSTER.
$69.99
808082, 812899 ONE (1) NEW CLUTCH or PTO 5/8" ID PILOT BEARING FOR CUSHMAN TRUCKSTER HAULSTER WITH OMC 9HP, 18HP, OR 22HP or 327 or Kawasaki ENGINE.
$14.99
812898 ONE (1) USED OMC CLUTCH MOUNTING PLATE CUSHMAN PART TRUCKSTER HAULSTER
$49.99
THIRTY TWO (32) PIECES OF STAINLESS STEEL 18-8 HARDWARE TO REPLACE THE CLUTCH BOLTS CUSHMAN/OMC SS.
$22.99
306971 SIX (6) NEW CLUTCH RELEASE YOKE LEVER ROLL PINS 3/16" X 1-1/4" TO REPLACE CUSHMAN PART
$4.99